PREDIKSI UMUR DAN KEANDALAN RIPPER TIP PADA BULLDOZER CATERPILLAR D10T DENGAN METODE WEIBULL

Fadhilah Akmal Rofiq Arifin, Braam Delfian Prihadianto, Sugiyanto Sugiyanto, Irfan Bahiuddin

Abstract


Ripper tip is one of the hard steel-based components on heavy equipment with a function to protect the ripper tip when breaking the density of soil and rock material (ripping). Friction between rock surfaces and ripper tips results in wear on ripper tips that require periodic replacement. Caterpillar D10T bulldozer owned by PT. XYZ underwent replacement ripper tip components that did not match the recommended age. This study aims to improve the accuracy of replacement planning and analyze the reliability level of ripper tip components. This study used the Weibull distribution method in analyzing the data. The data used is data on ordering and replacing ripper tip components from 2019 to 2021. The object of research was carried out on three units of Caterpillar D10T bulldozers used by PT. XYZ in an open pit mining project in Batulicin District, Tanah Bumbu Regency, South Kalimantan Province. This study shows that the average age of components in the three research objects has differences from the average life of ripper tip components on bulldozers A, B, and C is 369.75 hours, 329.63 hours, and 291.39 hours. The reliability of ripper tip components on the three bulldozers showed a decrease with the increase in operating time while the failure rate of the ripper tip components of the three bulldozers showed an increase with the increased operating time.


Keywords


lifetime prediction; reliability; bulldozer; ripper tip; Weibull

Full Text:

PDF Remote

References


M. F. Ullah et al., “Coal mining trends, approaches, and safety hazards: a brief review,” Arabian Journal of Geosciences, vol. 11, no. 21, p. 651, Nov. 2018, doi: 10.1007/s12517-018-3977-5.

R. Juniah, “Study of Carbon Value of the Allotment of Former Coal Mining Land of PT Samantaka Batubara for Sustainable Mining Environment,” J Sustain Dev, vol. 11, no. 4, p. 213, Jul. 2018, doi: 10.5539/jsd.v11n4p213.

Sujiman, “Evaluation of Ripper Productivity (Caterpillar D8R) Based on Strengthness of Rock at PT Kitadin Embalut Site Tenggarong Subdistrict Kutai Kartanegara East Kalimantan Province,” International Journal Of Accounting, Finance, And Economics, vol. 1, no. 1, pp. 1–9, 2018.

J. Wang and X. Zhu, “Joint optimization of condition-based maintenance and inventory control for a k-out-of-n:F system of multi-state degrading components,” Eur J Oper Res, vol. 290, no. 2, pp. 514–529, Apr. 2021, doi: 10.1016/j.ejor.2020.08.016.

M. Zheng, H. Ye, D. Wang, and E. Pan, “Joint Optimization of Condition-Based Maintenance and Spare Parts Orders for Multi-Unit Systems with Dual Sourcing,” Reliab Eng Syst Saf, vol. 210, p. 107512, Jun. 2021, doi: 10.1016/j.ress.2021.107512.

R. Wang and G. Chen, “Spare Parts Stocking Decision Strategy and Service Logistics Cost Optimization of Two-Echelon Service Logistics System considering Multifailure Mode,” Comput Intell Neurosci, vol. 2022, pp. 1–12, Mar. 2022, doi: 10.1155/2022/7607985.

G. D. Haryadi, G. E. Siburian, N. Iskandar, and R. J. Pribadi, “Metode Perhitungan Critical Component Lifetime Prediction Dan Keandalan Dengan Menggunakan Weibull Pada Coal Hauler Truck,” TRAKSI: Majalah Ilmiah Teknik Mesin, vol. 20, no. 1, pp. 24–44, 2020.

G. D. Haryadi, A. Suprihanto, M. Butarbutar, and J. H. Soedarto, “Perhitungan Lifetime Prediction pada Komponen Kritis Centrifugal Pump Menggunakan Metode Weibull,” ROTASI, vol. 23, no. 3, pp. 1–8, 2021.

L. Opyrchał, “Is Mean Time to Failure (MTTF) Equal to Mean Time of Life for Unrepairable Systems?,” Journal of KONBiN, vol. 51, no. 1, pp. 255–264, Mar. 2021, doi: 10.2478/jok-2021-0017.

T. N. Sindhu and A. Atangana, “Reliability analysis incorporating exponentiated inverse Weibull distribution and inverse power law,” Qual Reliab Eng Int, vol. 37, no. 6, pp. 2399–2422, Oct. 2021, doi: 10.1002/qre.2864.

L. Guo, Y. Liu, W. Zhang, P. Liu, T. Wang, and Q. Wu, “Research on Equipment RCM Maintenance Strategy Based on Importance Assessment and Online Fault Monitoring,” in 2022 Asia Power and Electrical Technology Conference (APET), IEEE, Nov. 2022, pp. 269–273. doi: 10.1109/APET56294.2022.10073244.

L. G. Otaya, “Distribusi Probabilitas Weibull Dan Aplikasinya (Pada Persoalan Keandalan (Reliability) Dan Analisis Rawatan (Mantainability),” Jurnal Manajemen Pendidikan Islam, vol. 4, no. 2, pp. 44–66, 2016.

R. Pebrianto, M. Asof, B. K. Susilo, and N. Gofar, “Evaluation of Factors Affecting Ripping Productivity in Open Pit Mining Excavation,” EJGE, vol. Vol. 19, pp. 10447–10456, 2014.

L. Ait El Maalem, M. E. H. Ech-Chhibat, Z. Znaidi, and A. Bahani, “Reliability study of welding robots,” in 2023 3rd International Conference on Innovative Research in Applied Science, Engineering and Technology (IRASET), IEEE, May 2023, pp. 1–6. doi:10.1109/IRASET57153.2023.10152972.

J. Galliková, V. Stuchlý, R. Poprocký, and P. Volna, “Model calculations of posterior reliability indicators for the proposal of the maintenance system,” MATEC Web of Conferences, vol. 157, p. 08003, Mar. 2018, doi: 10.1051/matecconf/201815708003.




DOI: https://doi.org/10.32487/jtt.v12i1.1860

Refbacks

  • There are currently no refbacks.


JTT (Jurnal Teknologi Terpadu) has been indexed by:

 

 

 

 

 

 

 

 

 

Web
Analytics

JTT Visitor Stats